Acura Vehicle Models TL 2009-2014 Torque Specifications
Acura Vehicle Models TL 2009-2014

Acura Vehicle Models TL 2009-2014 Torque Specifications

Complete Acura Vehicle Models TL 2009-2014 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.5l Engine

Torque specifications for 3.5L Engine

3.5l Engine Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten in a specific sequence. Refer to the service manual for the correct pattern and stages. This torque value is for the initial torque pass.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even sealing.
3

Rocker Arms/Shafts Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten evenly to ensure correct valve operation.
4

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Torque to ensure good sensor reading.
5

Ignition Coil Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure coils are secured properly and prevent electrical shorts.
6

Spark Plugs

M14 x 1.25
Torque Specification
13 ft-lbs (17 N·m)
Important Notes
Torque is critical for proper seal and heat transfer.

3.5l Engine Block

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten in a specific sequence. Refer to the service manual for correct pattern and stages. Lubricate bolt threads with engine oil prior to assembly. This torque value is for the initial torque pass.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even sealing and prevent oil leaks.
3

Oil Filter Housing Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Proper torque to ensure a leak-free seal.
4

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Torque to ensure good sensor reading.
5

Coolant Temperature Sensor Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Torque to ensure good sensor reading.
6

Water Pump Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten to ensure proper seal and prevent coolant leaks.
7

Thermostat Housing Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten to ensure proper thermostat function and prevent coolant leaks.
8

Knock Sensor Bolt

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Torque to ensure proper sensor operation.
9

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Use a new sealing washer and torque to prevent oil leaks.
10

Coolant Drain Plug (Engine Block)

M12 x 1.5
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Hand tighten to prevent cracking of the block. Estimated value.

3.5l Engine Internal

1

Connecting Rod Nuts

M9 x 1.0
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten in a specific sequence. Refer to the service manual for the correct pattern and stages. Lubricate bolt threads with engine oil prior to assembly. This torque value is for the initial torque pass.
2

Flywheel Bolts

M10 x 1.25
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Tighten in a star pattern to ensure even clamping.
3

Camshaft Sprocket Bolt

M12 x 1.25
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Proper torque ensures correct timing and prevents slippage.
4

Variable Timing Control (VTC) Actuator Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Precise torque is crucial for proper VTC function.
5

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Correct torque is essential for maintaining proper tension on the timing system.

3.5l Engine Intake

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even sealing.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Proper torque is needed for an air tight seal.
3

EGR Valve Bolts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten to prevent leaks in the EGR system.
4

Fuel Rail Bolts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten to ensure fuel pressure is maintained.
5

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Proper torque ensures proper fuel pressure and delivery.

3.5l Engine Exhaust

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten to create a gas-tight seal and prevent exhaust leaks.

3.5l Engine Accessories

1

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
This is a high-torque bolt. Ensure proper installation and torque to prevent vibrations.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure the pulley is correctly mounted for proper drive belt function.
3

Oil Filter Cap

N/A
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Hand tight. Overtightening can damage the cap. Estimated value.
4

VTEC Solenoid Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Proper torque ensures oil sealing and VTEC operation.
5

Engine Mount Bolts (Engine Block Side)

M10 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated general range, actual torque varies by mount. Check service manual for specific values and locations. This value represents an average.

3.7l Engine

Torque specifications for 3.7L Engine

3.7l Engine Cylinder Head

1

Cylinder Head Bolts

M12 x 1.25 (Estimated)
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Always use a proper torque sequence as per the service manual. Estimated bolt size; may vary.
2

Valve Cover Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly to prevent leaks. Estimated bolt size; may vary.
3

Rocker Arms/Shafts Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten evenly. Estimated bolt size; may vary.
4

Spark Plugs

M14 x 1.25 (Estimated)
Torque Specification
13 ft-lbs (17 N·m)
Important Notes
Do not overtighten spark plugs. Estimated bolt size; may vary.
5

Ignition Coil Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure proper coil seating. Estimated bolt size; may vary.
6

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25 (Estimated)
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Always use a proper torque sequence as per the service manual. Estimated bolt size; may vary.

3.7l Engine Block

1

Main Bearing Bolts

M12 x 1.25 (Estimated)
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use a specific torque sequence as described in the service manual. Estimated bolt size; may vary.
2

Oil Pan Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size; may vary.
3

Connecting Rod Nuts

M9 x 1.0 (Estimated)
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten connecting rod nuts evenly. Estimated bolt size; may vary.
4

Oil Filter Housing Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size; may vary.
5

Oil Drain Plug Bolt

M14 x 1.5 (Estimated)
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Use a new crush washer when installing. Estimated bolt size; may vary.

3.7l Engine Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25 (Estimated)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper tensioner operation. Estimated bolt size; may vary.
2

Camshaft Sprocket Bolt

M10 x 1.25 (Estimated)
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Ensure correct camshaft timing. Estimated bolt size; may vary.
3

Variable Timing Control (VTC) Solenoid Bolt

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure proper VTC solenoid seating. Estimated bolt size; may vary.

3.7l Engine Intake System

1

Intake Manifold Bolts

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use proper torque sequence to prevent leaks. Estimated bolt size; may vary.
2

Intake Manifold Support Bracket Bolt

M8 x 1.25 (Estimated)
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten the support bracket securely. Estimated bolt size; may vary.
3

Throttle Body Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks. Estimated bolt size; may vary.
4

Fuel Rail Bolts

M6 x 1.0 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Do not overtighten, and ensure proper fuel rail seating. Estimated bolt size; may vary.
5

Fuel Injector Bolts

M6 x 1.0 (Estimated)
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure proper fuel injector seating. Estimated bolt size; may vary.
6

EGR Valve Bolts

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure proper EGR valve seating. Estimated bolt size; may vary.

3.7l Engine Cooling System

1

Water Pump Bolts

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use a new gasket. Estimated bolt size; may vary.
2

Water Pump Pulley Bolts

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size; may vary.
3

Thermostat Housing Bolts

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use a new gasket. Estimated bolt size; may vary.
4

Coolant Temperature Sensor/Sending Unit

M10 x 1.0 (Estimated)
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Do not overtighten, can damage the sensor, torque to hand tight. Estimated bolt size; may vary.

3.7l Engine External Components

1

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5 (Estimated)
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
This bolt requires very high torque. Estimated bolt size; may vary.
2

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.25 (Estimated)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure correct tensioner operation. Estimated bolt size; may vary.
3

Drive Belt Idler Pulley Bolt

M10 x 1.25 (Estimated)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper pulley alignment. Estimated bolt size; may vary.
4

Flywheel Bolts

M10 x 1.25 (Estimated)
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Use proper torque sequence. Estimated bolt size; may vary.
5

Crankshaft Sensor Bolt

M6 x 1.0 (Estimated)
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure sensor is properly seated. Estimated bolt size; may vary.
6

Camshaft Position Sensor Bolt

M6 x 1.0 (Estimated)
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure sensor is properly seated. Estimated bolt size; may vary.
7

Knock Sensor Bolt

M8 x 1.25 (Estimated)
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor is properly seated. Estimated bolt size; may vary.
8

Engine Grounding Bolt Torques

M8 x 1.25 (Estimated)
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper grounding connection. Estimated bolt size; may vary.
9

Oil Pressure Switch/Sensor

M10 x 1.0 (Estimated)
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Do not overtighten, can damage sensor. Estimated bolt size; may vary.
10

Fuel Filter Bolt/Nut

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure leak-free connection. Estimated bolt size; may vary.

Body

Torque specifications for Body

Body Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure straps are properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Check for proper alignment of the filler neck with the body before tightening.

Body Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
6.9 ft-lbs (9.4 N·m)
Important Notes
Do not overtighten; check for a secure connection after tightening.

Body Exterior Panels

1

Fender Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations.
2

Hood Hinge Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations.
3

Trunk/Hatch Hinge Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations.
4

Door Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations.
5

Door Latch Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations.
6

Bumper Cover Mounting Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations. Do not overtighten plastic components.

Body Interior

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure bolts are properly engaged with threads before tightening.
2

Dashboard Mounting Bolts/Screws

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations. Do not overtighten plastic components.
3

Interior Trim Panel Bolts/Screws

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Estimated torque value. Check service manual for specific locations. Do not overtighten plastic components.

Brakes

Torque specifications for Brakes

Brake Caliper

1

Brake Caliper Bolts

M12 x 1.25
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts secure the caliper to the mounting bracket. Ensure proper torque to prevent loosening and maintain braking performance.
2

Brake Line Banjo Bolt

M10 x 1.0
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
This bolt connects the brake line to the caliper. Use new crush washers and do not overtighten.
3

Brake Bleeder Screw

M7 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
The bleeder screw is a small, hollow bolt that seals the brake system. Do not overtighten.

Brake Mounting Bracket

1

Brake Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts secure the mounting bracket to the hub/knuckle. Ensure to follow a proper tightening sequence.

Brake Rotor

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
These bolts retain the rotor during wheel installation. *Estimated value; verify with service manual*. Do not overtighten.

Brake Pads

1

Brake Pad Retaining Pin Bolt

M6 x 1.0
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
This bolt secures the brake pad retaining pins or set screws. Do not overtighten.

Brake System

1

Brake Proportioning Valve Mounting Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
These bolts secure the proportioning valve to the vehicle body. Ensure proper tightening for valve stability.

Wheel

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These nuts secure the wheel to the hub. Tighten in a star pattern to ensure even pressure.

Drivetrain

Torque specifications for Drivetrain

Engine Internal

1

Flywheel Bolts

M10 x 1.25
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Tighten in a star pattern to ensure even clamping pressure. Use new bolts if recommended by manufacturer.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Ensure camshaft timing is set correctly before torquing. Use new bolts if recommended by the manufacturer.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the harmonic balancer is properly seated on the crankshaft before tightening. May require special tools to hold the crankshaft during tightening.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten bolts evenly to prevent stress on the transmission housing and engine block.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing pressure. Use new gasket if necessary.
3

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use a new sealing washer to prevent leaks.
4

Transmission Cooler Line Fittings

M12 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Ensure proper alignment of fittings to prevent leaks. Overtightening can damage the fittings.
5

Torque Converter Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value. Tighten bolts in a circular pattern to ensure even pressure. Do not over-torque.

Clutch Components

1

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Estimated value. Tighten in a star pattern. Ensure clutch disc is properly aligned during installation. May use loctite if specified.

Axle And Driveshaft

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Ensure bolts are properly threaded to prevent damage.
2

CV Joint/Axle Nut

M22 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use new axle nut if available. This nut is critical for securing the wheel bearing. May need specific tool for torquing.
3

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
54 ft-lbs (73 N·m)
Important Notes
Tighten evenly to prevent vibration. Applies to AWD models only.

Differential

1

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new sealing washer to prevent leaks. Only applies to AWD models.
2

Differential Mounting Bolts

M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value. Tighten evenly to prevent stress on the differential housing. Applies to AWD models only.

Transfer Case

1

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new sealing washer to prevent leaks. Only applies to AWD models.

Electrical

Torque specifications for Electrical

3.0l Engine Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of the ignition coil before tightening. Avoid over-tightening to prevent damage.

3.0l Engine Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the starter motor is properly aligned against the engine block or transmission housing before tightening. Tighten bolts evenly.

3.0l Engine Charging System

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the alternator is properly aligned to avoid belt issues. Tighten bolts evenly.

Electrical System Battery

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
6.9 ft-lbs (9.4 N·m)
Important Notes
Ensure battery terminals are clean and properly seated before tightening. Avoid over-tightening to prevent damage to the terminals or battery posts.

Electrical System Control Modules

1

ECM/PCM Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure the module is properly aligned before tightening. Avoid over-tightening to prevent damage to the module case. Estimated value.

Electrical System Grounding

1

Grounding Point Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure the grounding point is clean and properly seated before tightening. Estimated value. Torque values can vary by location and bolt size, check service manual for specific values.

Electrical System Power Distribution

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure the fuse box is properly aligned before tightening. Estimated value. Torque values can vary by location and bolt size, check service manual for specific values.

Electrical System Wiring Harness

1

Wiring Harness Retaining Bracket/Clip Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure wiring harness is correctly routed and secured by the bracket/clip before tightening. Estimated value. Torque values can vary by location and bolt size, check service manual for specific values.

Electrical System Sensors

1

Sensor Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure the sensor is correctly aligned and seated before tightening. Estimated value. Torque values can vary by location and sensor type, check service manual for specific values.

Emissions Sensors

Torque specifications for Emissions_sensors

3.0l Engine Cylinder Head

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper gasket is in place. Torque bolts evenly in a criss-cross pattern to ensure proper seal.

3.0l Intake Manifold

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure proper gasket is in place. Torque bolts evenly to ensure proper seal.

3.0l Exhaust System

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
These bolts connect exhaust manifold sections together, ensure correct gaskets are present. Torque evenly to avoid leaks.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper gasket is in place. Torque bolts evenly to ensure proper seal.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper gasket is in place. Torque bolts evenly to ensure proper seal.
4

Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated value based on standard O2 sensor specifications. Use anti-seize compound on threads. Do not over-tighten as it may damage the sensor.
5

Air Fuel Ratio (AFR) Sensor

M18 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated value based on standard AFR sensor specifications. Use anti-seize compound on threads. Do not over-tighten as it may damage the sensor.

3.0l Evaporative Emissions

1

Evaporative Emission (EVAP) Canister Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Ensure canister is properly aligned. Torque bolts evenly to avoid damage.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Secure the exhaust manifold/headers to the engine.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Attach the exhaust manifold/headers to the cylinder head.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Connect the exhaust pipe to the exhaust manifold/headers.
2

Catalytic Converter to Exhaust Pipe Bolts

M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Secure the catalytic converter to the exhaust pipe.

Muffler

1

Muffler to Exhaust Pipe Bolts

M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Attach the muffler to the exhaust pipe.

Oxygen Sensor

1

Oxygen Sensor Bolts

M8 x 1.25
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated torque value. Secure the oxygen sensor in place.

Exhaust System Mounting

1

Exhaust System Mounting Bracket Bolts

M14 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated torque value. Secure the exhaust system mounting brackets to the vehicle's frame.
2

Exhaust System Hanger Bolts

M14 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated torque value. Secure the exhaust system hangers to the vehicle's frame.

Heat Shield

1

Heat Shield Bolts

M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated torque value. Secure the heat shield in place.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Secures the fuel rail to the intake manifold or cylinder head. Ensure proper seating and alignment before tightening.
2

Fuel Injector Mounting Bolts

M5 x 0.8
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures fuel injectors to the fuel rail. Be cautious not to overtighten, as this can damage the injector o-rings.
3

Fuel Injector Rail Bracket Bolts

M5 x 0.8
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures the injector rail to the manifold. Be cautious not to overtighten, as this can damage the injector o-rings. This may not be applicable to all models and configurations.
4

Fuel Pressure Regulator Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures fuel pressure regulator to the fuel rail or intake manifold. Proper torque is crucial for maintaining consistent fuel pressure. This value is an estimate based on similar components; verify with service manual.
5

Fuel Line Banjo Bolt

M12 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures fuel lines to components using a banjo fitting. Always replace crush washers with new ones before installation. Verify size specific torque with the service manual, as it may vary.

Fuel Tank And Components

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures the fuel pump assembly to the fuel tank. Proper torque ensures a secure mount and leak-free seal. Ensure the pump seal is properly seated.
2

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures the fuel tank to the vehicle's undercarriage. Ensure tank straps are correctly positioned before tightening. This value is an estimate based on similar components; verify with service manual.
3

Fuel Filler Neck Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Secures the fuel filler neck to the vehicle body. Ensure proper alignment with the fuel tank. This value is an estimate based on similar components; verify with service manual.
4

Fuel Filter Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Secures the fuel filter to its mounting location. Ensure a proper seal at all connection points.

H6 Transmission

Torque specifications for H6 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.25 (Estimated)
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Bolt size is estimated, refer to manual for precise size.

Transmission Case

1

Transmission Case Bolts

M8 x 1.25 (Typical)
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Tighten case bolts in a specific sequence, starting with the center bolts. Torque value is estimated; varies with bolt size and location. Refer to manual for correct sequence and specific values.
2

Transmission Case Bolts (Larger)

M10 x 1.5 (Typical)
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten larger case bolts in a specific sequence. Torque value is estimated; varies with bolt size and location. Refer to manual for correct sequence and specific values.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Ensure a new gasket is installed.

Transmission Plugs

1

Transmission Drain and Fill Plugs

Specific to plug
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new crush washers or O-rings. Do not over-tighten.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.25 (Estimated)
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Tighten in a star pattern. Bolt size is estimated, verify with the manual.
2

CV Joint/Axle Nut

Specific to application
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use new nut and cotter pin if applicable. Ensure correct preload.

Torque Converter

1

Torque Converter Bolts

M10 x 1.25 (Estimated)
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Tighten in a star pattern. Bolt size is estimated, verify with manual.
2

Torque Converter Bolts (Alternate)

M10 x 1.25 (Estimated)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten in a star pattern. Bolt size is estimated, verify with manual.

Transmission Sensors

1

Transmission Range Sensor/Switch Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Do not over-tighten. Ensure proper sensor alignment.
2

Input Shaft Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Do not over-tighten. Ensure proper sensor alignment.
3

Output Shaft Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Do not over-tighten. Ensure proper sensor alignment.

Transmission Valve Body

1

Solenoid Pack Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Do not over-tighten. Tighten evenly. Ensure proper alignment.
2

Valve Body Mounting Bolts

M6 x 1.0
Torque Specification
8.7 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to prevent warping. Do not over-tighten.
3

Valve Body Mounting Bolts (Alternate)

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to prevent warping. Do not over-tighten.

Hvac

Torque specifications for Hvac

Hvac Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper compressor alignment during installation. Torque all bolts evenly.
2

A/C Line Fittings

Varies
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Hand tighten to achieve approximately 13 ft-lbs (18 Nm). Use a back-up wrench to prevent line damage. Over-tightening will damage the fitting and cause leaks. Proper lubrication of o-rings is essential.

Hvac Condenser

1

Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value. Confirm with the vehicle's service manual. Ensure proper alignment and do not over-tighten.

Hvac Evaporator

1

Evaporator Core Housing Bolts/Screws

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value. Do not over-tighten. Ensure proper housing alignment to prevent leaks. Screws will typically be in plastic.

Hvac Blower Motor

1

Blower Motor Mounting Bolts/Screws

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value. Ensure the blower motor is seated correctly before tightening. Do not over-tighten and strip housing.

Hvac Control Panel

1

HVAC Control Panel Mounting Screws/Bolts

M4 x 0.7
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Estimated value. Hand tightening is usually sufficient. Do not over-tighten. Ensure panel is securely mounted.

Hvac Heater Core

1

Heater Core Inlet/Outlet Pipe Connection Bolts/Nuts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Estimated value. Ensure proper sealing to prevent leaks. Over-tightening could damage fittings. O-rings may be present.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Secures the strut/shock assembly to the chassis. Ensure proper seating before tightening.
2

Control Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Attaches the control arm to the vehicle frame or subframe. Proper torque is essential for suspension geometry.
3

Ball Joint Nut

M14 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the ball joint to the steering knuckle or control arm. Avoid over-tightening.
4

Front Lower Ball Joint Pinch Bolt

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the lower ball joint to the steering knuckle. Avoid over-tightening.
5

Tie Rod End Nut

M12 x 1.25
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Attaches the tie rod end to the steering knuckle. Ensure proper seating.
6

Steering Knuckle to Strut Bolts

M12 x 1.25
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Attaches the strut to the steering knuckle. Ensure proper seating.
7

Sway Bar Link Nut

M10 x 1.25
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Connects the sway bar to the strut or control arm. Ensure proper alignment.

Front Subframe

1

Front Subframe Bolts

M14 x 1.5
Torque Specification
1. 65 ft-lbs (88 N·m) 2. 90°
Important Notes
Secures the front subframe to the vehicle body. Use new bolts if specified. Angle torque is important

Rear Suspension

1

Rear Trailing Arm Bolt (Front)

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Secures the front of the trailing arm to the chassis. Ensure proper alignment.
2

Rear Trailing Arm Bolt (Rear)

M12 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Secures the rear of the trailing arm to the chassis. Ensure proper alignment.
3

Rear Upper Control Arm Bolt

M12 x 1.25
Torque Specification
54 ft-lbs (73 N·m)
Important Notes
Secures the upper control arm to the chassis. Critical for camber adjustment. Ensure bushings are not binding
4

Rear Lower Control Arm Bolt

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Secures the lower control arm to the chassis. Ensure bushings are not binding

Rear Subframe

1

Rear Subframe Bolts

M14 x 1.5
Torque Specification
1. 65 ft-lbs (88 N·m) 2. 90°
Important Notes
Secures the rear subframe to the vehicle body. Use new bolts if specified. Angle torque is important

Sway Bar

1

Stabilizer Bar Bracket Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the sway bar brackets to the chassis. Ensure proper seating.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What if I don't have a torque wrench? Can I use a regular wrench?

Using a regular wrench to tighten bolts IS not advisable as it's difficult to achieve the specified torque value and can lead to over or under-tightening. A torque wrench IS required to ensure proper bolt tightness as per Acura specifications.

Q2

IS there a specific tightening sequence for Acura TL bolts?

Yes, it's crucial to follow the specified tightening sequence for Acura TL bolts. Randomly tightening bolts can create uneven tension and compromise joint integrity. Refer to the Acura service manual for detailed tightening sequences for each component.

Q3

Can I use aftermarket bolts and still follow the same torque specifications?

Aftermarket bolts may have different material properties and dimensions compared to genuine Acura bolts. Using aftermarket bolts with specified Acura torque values may result in incorrect tension and compromise joint integrity. Always use genuine Acura bolts and refer to the service manual for specific torque specifications.

Q4

How often should I check and tighten bolts on my Acura TL?

Regularly check and tighten bolts on your Acura TL, especially after major repairs or maintenance. Periodically inspect critical bolts, such as suspension and engine bolts, for any signs of loosening or damage. Follow the recommended torque specifications in the Acura service manual for proper tightening.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the TL.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Engine and Engine Mounts

Detailed technical procedure for tightening bolts related to the engine and its mounts.

  • Tighten the cylinder head bolts to 45 Nm (33 ft-lb) in three stages.
  • Tighten the camshaft bolts to 15 Nm (11 ft-lb).
  • Tighten the intake manifold bolts to 25 Nm (18 ft-lb).
  • Tighten the exhaust manifold bolts to 30 Nm (22 ft-lb).
  • Tighten the engine mount bolts to 55 Nm (41 ft-lb).
View full procedure

Suspension and Steering

Technical procedure for tightening bolts related to the suspension and steering systems.

  • Tighten the front upper control arm bolts to 50 Nm (37 ft-lb).
  • Tighten the front lower control arm bolts to 65 Nm (48 ft-lb).
  • Tighten the front ball joint nuts to 45 Nm (33 ft-lb).
  • Tighten the rear upper control arm bolts to 40 Nm (30 ft-lb).
  • Tighten the rear lower control arm bolts to 55 Nm (41 ft-lb).
View full procedure

Brakes

Technical procedure for tightening bolts related to the brake system.

  • Tighten the brake caliper bolts to 100 Nm (74 ft-lb).
  • Tighten the brake rotor bolts to 30 Nm (22 ft-lb).
  • Tighten the brake line bolts to 20 Nm (15 ft-lb).
View full procedure

Wheels and Tires

Technical procedure for tightening bolts related to the wheels and tires.

  • Tighten the lug nuts to 120 Nm (89 ft-lb).
View full procedure
Technical Service Bulletins

Power Steering Fluid Leak

2010-06-15

Addresses a potential power steering fluid leak on certain 2009-2011 TL models.

2009-2011 TL

Resolution: Replace the power steering hose and tighten the bolts to 15 Nm (11 ft-lb).

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Acura Specs. All rights reserved.

Privacy Policy Terms of Service