Acura Vehicle Models RLX 2014-2020
Acura Vehicle Models RLX 2014-2020 Torque Specifications
Complete Acura Vehicle Models RLX 2014-2020 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.5l Engine
Torque specifications for 3.5L Engine
3.5l Engine
Torque specifications for 3.5L Engine
3.5l Engine Cylinder Head
1 Cylinder Head Bolts
M11 x 1.5
1
Cylinder Head Bolts
M11 x 1.5
Torque Specification
1. 16 ft-lbs (22 N·m)
2. 90°
Important Notes
Initial torque, followed by a 90 degree angle torque. Use a proper cylinder head torque sequence pattern.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure proper alignment of rocker arm components before tightening.
3 Camshaft Cap Bolts/Nuts
M8 x 1.25
3
Camshaft Cap Bolts/Nuts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value. Use a proper torque sequence.
4 Spark Plugs
M14 x 1.25
4
Spark Plugs
M14 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Do not overtighten. Use a proper spark plug socket.
5 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
5
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use a criss-cross tightening pattern to ensure even pressure on the manifold gasket.
3.5l Engine Block
1 Main Bearing Bolts
M10 x 1.5
1
Main Bearing Bolts
M10 x 1.5
Torque Specification
1. 29 ft-lbs (39 N·m)
2. 60°
Important Notes
Initial torque, followed by a 60 degree angle torque. Always use a proper main bearing torque sequence.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 60°
Important Notes
Initial torque, followed by a 60 degree angle torque. Use a proper connecting rod torque sequence.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Use a proper torque sequence to ensure an even seal.
4 Water Pump Bolts
M8 x 1.25
4
Water Pump Bolts
M8 x 1.25
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Do not overtighten. Use a criss-cross pattern.
5 Oil Drain Plug Bolt
M14 x 1.5
5
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Use a new crush washer.
6 Starter Motor Mounting Bolts
M10 x 1.5
6
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment before tightening.
7 Alternator Mounting Bolts
M10 x 1.5
7
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment before tightening.
3.5l Engine Intake
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use a proper torque sequence to ensure an even seal.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Do not overtighten. Use a criss-cross pattern.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure proper alignment before tightening.
4 Fuel Rail Bolts
M6 x 1.0
4
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Do not overtighten. Use a criss-cross pattern.
5 Fuel Injector Bolts
M6 x 1.0
5
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper alignment before tightening.
6 Knock Sensor Bolt
M8 x 1.25
6
Knock Sensor Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Do not overtighten.
3.5l Engine Cooling
1 Thermostat Housing Bolts
M6 x 1.0
1
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Use a new gasket. Do not overtighten.
2 Engine Coolant Temperature (ECT) Sensor
M12 x 1.5
2
Engine Coolant Temperature (ECT) Sensor
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Use a new crush washer if applicable.
3 Water Pump Pulley Bolts
M6 x 1.0
3
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper alignment before tightening. Use a criss-cross tightening pattern.
3.5l Engine Accessory
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment before tightening.
2 Drive Belt Idler Pulley Bolt
M10 x 1.5
2
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment before tightening.
3 A/C Compressor Mounting Bolts
M10 x 1.5
3
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment before tightening.
3.5l Engine Timing
1 Timing Belt/Chain Tensioner Bolt
M10 x 1.5
1
Timing Belt/Chain Tensioner Bolt
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper tensioner operation after installation.
2 Camshaft Sprocket Bolt
M12 x 1.25
2
Camshaft Sprocket Bolt
M12 x 1.25
Torque Specification
94 ft-lbs (127 N·m)
Important Notes
Ensure proper alignment of timing marks before tightening.
3.5l Engine Flywheel
1 Flywheel Bolts
M12 x 1.25
1
Flywheel Bolts
M12 x 1.25
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Use new bolts. Use a criss-cross pattern.
3.5l Engine Crankshaft
1 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
1
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure proper alignment before tightening.
3.5l Engine Other
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Use a new gasket or sealer if required. Do not overtighten.
2 Ignition Coil Bolt
M6 x 1.0
2
Ignition Coil Bolt
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper alignment before tightening.
3 Oil Filter Cap
N/A
3
Oil Filter Cap
N/A
Torque Specification
N/A
Important Notes
Hand tight only, do not overtighten.
4 Oil Filter Housing Bolt
N/A
4
Oil Filter Housing Bolt
N/A
Torque Specification
N/A
Important Notes
Hand tight only, do not overtighten.
Body
Torque specifications for Body
Body
Torque specifications for Body
Body Fuel System
1 Fuel Tank Strap Bolts
M10 x 1.25
1
Fuel Tank Strap Bolts
M10 x 1.25
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Tighten bolts evenly to secure fuel tank straps.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment before tightening. Do not over-tighten.
Body Electrical
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
5.1 ft-lbs (7 N·m)
Important Notes
Ensure terminals are clean and free of corrosion before tightening.
Body Chassis
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Tighten lug nuts in a star pattern. Re-check after 50-100 miles.
2 Seat Mounting Bolts
M8 x 1.25
2
Seat Mounting Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value. Ensure proper seat alignment before final tightening.
Body Exterior
1 Bumper Mounting Bolts/Fasteners
M8 x 1.25
1
Bumper Mounting Bolts/Fasteners
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Check alignment and fit before final tightening. Ensure fasteners are correctly seated.
2 Hood Hinge Bolts
M8 x 1.25
2
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Check hood alignment and proper operation after tightening.
3 Fender Mounting Bolts/Fasteners
M6 x 1.0
3
Fender Mounting Bolts/Fasteners
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value. Do not over-tighten. Check panel alignment and fit before final tightening.
4 Door Hinge Bolts
M10 x 1.5
4
Door Hinge Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated Value. Ensure proper door alignment and function after tightening.
5 Door Latch/Striker Bolts
M8 x 1.25
5
Door Latch/Striker Bolts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value. Ensure smooth door latch operation after tightening.
6 Headlight/Taillight Mounting Bolts/Screws
M6 x 1.0
6
Headlight/Taillight Mounting Bolts/Screws
M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten plastic components. Check for proper alignment.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brakes Caliper
1 Brake Caliper Mounting Bolts
M12 x 1.25
1
Brake Caliper Mounting Bolts
M12 x 1.25
Torque Specification
79 ft-lbs (108 N·m)
Important Notes
Secures the brake caliper directly to the mounting bracket. Ensure both bolts are torqued evenly.
2 Brake Caliper Bleeder Screw
M10 x 1.0
2
Brake Caliper Bleeder Screw
M10 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque to the middle of the specified range to prevent damage and ensure proper sealing.
3 Brake Line Fitting
M10 x 1.0 (estimated)
3
Brake Line Fitting
M10 x 1.0 (estimated)
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Connects brake line to caliper. Estimated value based on typical brake line fitting size and material.
4 Brake Pad Retaining Pin Bolt
M8 x 1.25
4
Brake Pad Retaining Pin Bolt
M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Secures the brake pad retaining pins. Ensures proper pad retention. If pins are secured by a different method, this torque spec will not be applicable.
Brakes Mounting Bracket
1 Brake Caliper Mounting Bracket Bolts
M14 x 1.5
1
Brake Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
79 ft-lbs (108 N·m)
Important Notes
Secures the mounting bracket to the wheel knuckle. Ensure bolts are evenly torqued.
Brakes Rotor
1 Brake Disc/Drum Retaining Bolts
M6 x 1.0
1
Brake Disc/Drum Retaining Bolts
M6 x 1.0
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
These bolts hold the rotor flush against the hub temporarily. They do not hold the rotor in place after the wheel is mounted.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine Flywheel
1 Flywheel Bolts
M12 x 1.25
1
Flywheel Bolts
M12 x 1.25
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Apply thread locker. Tighten bolts in a star pattern.
Transmission Housing
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Tighten bolts in a cross pattern.
2 Transmission-to-Engine Bolts
M12 x 1.75
2
Transmission-to-Engine Bolts
M12 x 1.75
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Tighten bolts in a cross pattern.
3 Input Shaft Bearing Retainer Bolts
M8 x 1.25
3
Input Shaft Bearing Retainer Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a cross pattern. Estimated value.
4 Output Shaft Bearing Retainer Bolts
M8 x 1.25
4
Output Shaft Bearing Retainer Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a cross pattern. Estimated value.
5 Transmission Oil Pan Bolts
M6 x 1.0
5
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Tighten bolts in a cross pattern
Transmission Fluid
1 Transmission Fluid Drain and Fill Plugs
M18 x 1.5
1
Transmission Fluid Drain and Fill Plugs
M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new sealing washers each time. Do not over tighten.
2 Automatic Transmission Fluid Cooler Line Bolts
M6 x 1.0
2
Automatic Transmission Fluid Cooler Line Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated Value. Do not over tighten.
Drive Axle System
1 Drive Axle/Half Shaft Bolts
M10 x 1.5
1
Drive Axle/Half Shaft Bolts
M10 x 1.5
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Tighten bolts in a star pattern.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Use new axle nut and cotter pin or locking device after torquing.
Propeller Shaft
1 Propeller/Drive Shaft Bolts
M10 x 1.5
1
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
54 ft-lbs (73 N·m)
Important Notes
Tighten bolts in a star pattern
Differential
1 Differential Mounting Bolts
M12 x 1.75
1
Differential Mounting Bolts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten bolts in a cross pattern. Estimated value. Torque may vary depending on axle model.
2 Differential Drain and Fill Plugs
M18 x 1.5
2
Differential Drain and Fill Plugs
M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new sealing washers each time. Do not over tighten.
3 Ring Gear Bolts
M12 x 1.5
3
Ring Gear Bolts
M12 x 1.5
Torque Specification
1. 65 ft-lbs (88 N·m)
2. 90°
Important Notes
Tighten bolts in a star pattern and then angle tighten an additional 90 degrees. Estimated Value. Torque may vary depending on axle model.
Transfer Case
1 Transfer Case Drain and Fill Plugs
M18 x 1.5
1
Transfer Case Drain and Fill Plugs
M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Use new sealing washers each time. Do not over tighten.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Mounting Bolt
M6 x 1.0
1
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper seating of the coil before tightening. Over-tightening can damage coil mounting point or coil housing.
Starting System
1 Starter Motor Mounting Bolt
M10 x 1.5
1
Starter Motor Mounting Bolt
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel/flexplate before tightening. Overtightening can damage the starter housing or engine block.
Charging System
1 Alternator Mounting Bolt
M10 x 1.5
1
Alternator Mounting Bolt
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment of the alternator with the belt before tightening. Over-tightening can damage the alternator bracket or engine block. Improper tightening can lead to belt slippage.
Battery System
1 Battery Terminal Nut
M6 x 1.0
1
Battery Terminal Nut
M6 x 1.0
Torque Specification
5.1 ft-lbs (7 N·m)
Important Notes
Do not over-tighten. Overtightening can damage the battery terminal. Ensure the terminal and nut are clean before tightening.
Engine Control System
1 ECM/PCM Mounting Bolt
M6 x 1.0
1
ECM/PCM Mounting Bolt
M6 x 1.0
Torque Specification
8.5 ft-lbs (11.5 N·m)
Important Notes
This is an estimated value based on typical ECM/PCM mounting bolts. Do not overtighten. Ensure proper seating before tightening.
Grounding System
1 Ground Strap/Wire Attachment Bolt (Body/Chassis)
M6 x 1.0
1
Ground Strap/Wire Attachment Bolt (Body/Chassis)
M6 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
This is an estimated value for common ground point bolts. Ensure the contact points are clean and free of corrosion.
Fuse Box
1 Fuse Box Mounting Bolt
M6 x 1.0
1
Fuse Box Mounting Bolt
M6 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
This is an estimated value. Do not overtighten. Ensure proper seating before tightening.
Lighting System
1 Headlight Mounting Bolt
M5 x 0.8
1
Headlight Mounting Bolt
M5 x 0.8
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
This is an estimated value for typical headlight mounting bolts. Do not overtighten. Ensure proper alignment before tightening.
2 Tail Light Mounting Bolt
M5 x 0.8
2
Tail Light Mounting Bolt
M5 x 0.8
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
This is an estimated value for typical taillight mounting bolts. Do not overtighten. Ensure proper alignment before tightening.
Sensor System
1 Sensor Mounting Bolt (Various)
M5 x 0.8
1
Sensor Mounting Bolt (Various)
M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
This is an estimated value for common sensor mounting bolts. Do not overtighten. Ensure proper seating before tightening. Check for sensor specific torque specs in service manual.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
3.0l Engine Cylinder Head
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten bolts in a criss-cross pattern, working from the center outwards. Ensure mating surfaces are clean.
3.0l Engine Exhaust System
1 Exhaust Manifold/Headers Bolts
M10 x 1.5
1
Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Apply an anti-seize compound to the threads. Tighten in a progressive, circular pattern.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure flange faces are properly aligned and clean before tightening.
3 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
3
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use new gaskets. Tighten evenly to prevent leaks.
4 Muffler to Exhaust Pipe Bolts
M10 x 1.5
4
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Check the alignment before tightening. Use new gaskets if required.
5 Oxygen (O2) Sensor
18mm Thread
5
Oxygen (O2) Sensor
18mm Thread
Torque Specification
31 ft-lbs (42 N·m)
Important Notes
Apply anti-seize compound on sensor threads. Do not overtighten
6 Air/Fuel Ratio (AFR) Sensor
18mm Thread
6
Air/Fuel Ratio (AFR) Sensor
18mm Thread
Torque Specification
31 ft-lbs (42 N·m)
Important Notes
Apply anti-seize compound on sensor threads. Do not overtighten
7 NOx Sensor
18mm Thread
7
NOx Sensor
18mm Thread
Torque Specification
31 ft-lbs (42 N·m)
Important Notes
Apply anti-seize compound on sensor threads. Do not overtighten.
8 Exhaust Backpressure Sensor
1/8" NPT Thread
8
Exhaust Backpressure Sensor
1/8" NPT Thread
Torque Specification
11.08 ft-lbs (15 N·m)
Important Notes
Apply thread sealant. Do not overtighten.
3.0l Engine Intake System
1 Mass Air Flow (MAF) Sensor Mounting Bolts
M5 x 0.8
1
Mass Air Flow (MAF) Sensor Mounting Bolts
M5 x 0.8
Torque Specification
5.92 in-lbs (8 N·m)
Important Notes
Do not overtighten, plastic housing can break easily.
2 Intake Air Temperature (IAT) Sensor
M6 x 1.0
2
Intake Air Temperature (IAT) Sensor
M6 x 1.0
Torque Specification
4.42 in-lbs (6 N·m)
Important Notes
Sensor housing is fragile, hand tight is often sufficient, use low torque.
3.0l Engine Egr System
1 EGR Valve Bolts
M8 x 1.25
1
EGR Valve Bolts
M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure mating surfaces are clean before installation.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
3.0l Engine Cylinder Head
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Always use new gaskets during installation. Ensure that all bolts are clean and have a light coat of anti-seize compound on threads. It is assumed these are M10 bolts with standard 1.25 thread pitch.
3.0l Exhaust System
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Always use new gaskets during installation. Ensure that all bolts are clean and have a light coat of anti-seize compound on threads. It is assumed these are M10 bolts with standard 1.5 thread pitch.
2 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Always use new gaskets during installation. Ensure that all bolts are clean and have a light coat of anti-seize compound on threads. It is assumed these are M10 bolts with standard 1.5 thread pitch.
3 Muffler to Exhaust Pipe Bolts
M10 x 1.5
3
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Always use new gaskets during installation. Ensure that all bolts are clean and have a light coat of anti-seize compound on threads. It is assumed these are M10 bolts with standard 1.5 thread pitch. Note that slip fit joints may require a clamp instead of bolts.
4 Exhaust Pipe Hanger Bolts/Nuts
M8 x 1.25
4
Exhaust Pipe Hanger Bolts/Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These are estimated values based on common M8 bolt sizes. Ensure all hangers are properly aligned and not under tension. Lightly lubricate bolts before install. Note: Sizes and torque specifications may vary based on specific design.
5 Exhaust Flange Studs
M10 x 1.5
5
Exhaust Flange Studs
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Torque studs into the exhaust component to ensure a proper mating surface. Ensure that threads are clean and have a light coating of anti-seize compound. It is assumed these are M10 studs with standard 1.5 thread pitch.
3.0l Exhaust Sensors
1 Oxygen Sensor
M18 x 1.5
1
Oxygen Sensor
M18 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure the sensor threads are clean and lightly lubricated. Do not overtighten. This is an estimate based on standard oxygen sensor thread size and materials.
3.0l Exhaust Heat Shields
1 Heat Shield Bolts/Nuts
M6 x 1.0
1
Heat Shield Bolts/Nuts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These are estimated values based on common M6 bolt sizes used for heat shields. Ensure heat shields are properly aligned and do not interfere with other components. Lightly lubricate bolts before install. Note: Sizes and torque specifications may vary based on specific design.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Delivery System
1 Fuel Rail Mounting Bolts
M6 x 1.0
1
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper seating of fuel rail before tightening. Tighten all bolts evenly to prevent warping.
2 Fuel Injector Mounting Bolts/Fasteners
M5 x 0.8
2
Fuel Injector Mounting Bolts/Fasteners
M5 x 0.8
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure injectors are properly seated into the fuel rail and intake manifold before tightening. Do not overtighten.
3 Fuel Pump Mounting Bolts
M6 x 1.0
3
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper seating of the fuel pump assembly onto the fuel tank. Do not overtighten and damage the gasket or o-ring seal.
4 Fuel Filter Mounting Bolt/Nut
M8 x 1.25
4
Fuel Filter Mounting Bolt/Nut
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper installation of the filter element. Do not overtighten.
5 Fuel Line Connection Fittings
Varies, typically M10-M14
5
Fuel Line Connection Fittings
Varies, typically M10-M14
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Torque value is an estimate, as fitting sizes can vary widely. Always consult service manual when possible. Use line wrenches to avoid rounding and damaging the fittings. Do not overtighten.
Fuel Tank And Filler
1 Fuel Filler Neck Mounting Bolts
M6 x 1.0
1
Fuel Filler Neck Mounting Bolts
M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the fuel filler neck before tightening. Do not overtighten.
Evaporative Emissions System
1 EVAP System Purge Valve Mounting Bolts
M6 x 1.0
1
EVAP System Purge Valve Mounting Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Ensure proper seating of the purge valve. Do not overtighten.
H6 Transmission
Torque specifications for H6 Transmission
H6 Transmission
Torque specifications for H6 Transmission
H6 Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
These bolts secure the transmission to the engine block and/or vehicle frame. Proper torque is critical for alignment and stability.
H6 Transmission Case
1 Transmission Case/Housing Bolts
M8 x 1.25
1
Transmission Case/Housing Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated torque value. Consult service manual for specific pattern. These bolts secure the transmission housing components together.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Proper torque is critical to prevent leaks and damage to the oil pan. Do not overtighten.
H6 Transmission Sensors
1 Transmission Range Sensor/Neutral Safety Switch Bolts
M6 x 1.0
1
Transmission Range Sensor/Neutral Safety Switch Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Estimated torque value. Ensure correct sensor positioning. Do not overtighten.
2 Transmission Speed Sensor Bolts
M6 x 1.0
2
Transmission Speed Sensor Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Estimated torque value. Ensure correct sensor positioning. Do not overtighten.
H6 Transmission Fluid System
1 Transmission Drain and Fill Plugs
M18 x 1.5
1
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Proper torque prevents leaks and damage to the plugs/case.
2 Transmission Cooler Line Fittings
M12 x 1.5 (Banjo Bolt)
2
Transmission Cooler Line Fittings
M12 x 1.5 (Banjo Bolt)
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated torque value. Over-tightening can cause leaks or damage. Use new sealing washers.
H6 Transmission Driveline
1 Drive Axle/Half Shaft Bolts
M10 x 1.25
1
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Proper torque is essential for reliable power transfer. Use threadlocker if specified.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Hvac Compressor
1 A/C Compressor Mounting Bolts
M8 x 1.25
1
A/C Compressor Mounting Bolts
M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the compressor is properly aligned on its mounting bracket before tightening. Use a cross-tightening pattern.
2 A/C Line Fittings
Varies, typically M6 x 1.0
2
A/C Line Fittings
Varies, typically M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Use two wrenches to avoid twisting the lines, one to hold the fitting and one to tighten. Ensure O-rings are properly seated and in good condition. Do not over-tighten.
Hvac Condenser
1 A/C Condenser Mounting Bolts
M6 x 1.0
1
A/C Condenser Mounting Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Estimated value based on typical M6 bolt application. Ensure proper alignment to avoid stressing the condenser. Do not over-tighten.
Hvac Evaporator
1 A/C Evaporator Housing Bolts
M6 x 1.0
1
A/C Evaporator Housing Bolts
M6 x 1.0
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Estimated value based on typical M6 bolt application. Tighten bolts in a criss-cross pattern to evenly compress the seal. Avoid over-tightening to prevent cracking plastic parts.
2 A/C Expansion Valve Bolts/Screws
M6 x 1.0 or smaller
2
A/C Expansion Valve Bolts/Screws
M6 x 1.0 or smaller
Torque Specification
8.7 ft-lbs (11.8 N·m)
Important Notes
Estimated value based on typical small bolts for this application. Ensure the expansion valve is properly seated. Do not over-tighten. This valve usually uses an o-ring for sealing.
Hvac Blower Motor
1 HVAC Blower Motor Mounting Bolts/Screws
M5 x 0.8 or smaller
1
HVAC Blower Motor Mounting Bolts/Screws
M5 x 0.8 or smaller
Torque Specification
4.3 ft-lbs (5.9 N·m)
Important Notes
Ensure blower motor is properly seated before tightening. Do not over-tighten due to plastic components.
Hvac Actuators
1 HVAC Mode/Airflow Door Actuator Mounting Screws
M4 x 0.7 or smaller
1
HVAC Mode/Airflow Door Actuator Mounting Screws
M4 x 0.7 or smaller
Torque Specification
1.8 ft-lbs (2.5 N·m)
Important Notes
Do not over-tighten due to plastic components. Ensure correct actuator alignment before tightening.
2 HVAC Blend Door Actuator Mounting Screws
M4 x 0.7 or smaller
2
HVAC Blend Door Actuator Mounting Screws
M4 x 0.7 or smaller
Torque Specification
1.8 ft-lbs (2.5 N·m)
Important Notes
Do not over-tighten due to plastic components. Ensure correct actuator alignment before tightening.
Hvac Sensors
1 A/C Pressure Switch
Varies, generally no specified size as it threads directly into the manifold
1
A/C Pressure Switch
Varies, generally no specified size as it threads directly into the manifold
Torque Specification
N/A
Important Notes
Hand tight plus 1/8 turn past hand tight. Do not use a torque wrench.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Suspension
1 Strut/Shock Absorber Mounting Bolts
M12 x 1.75
1
Strut/Shock Absorber Mounting Bolts
M12 x 1.75
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Secures the strut/shock absorber to the chassis and/or steering knuckle.
2 Upper Strut Mount Nut
M10 x 1.5
2
Upper Strut Mount Nut
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the top of the strut assembly to the vehicle's chassis. Estimated value based on common nut size.
3 Control Arm Bolts
M14 x 2.0
3
Control Arm Bolts
M14 x 2.0
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Attaches the control arms to the vehicle's frame/subframe.
4 Front Lower Control Arm to Ball Joint Pinch Bolt
M10 x 1.5
4
Front Lower Control Arm to Ball Joint Pinch Bolt
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Clamps the ball joint stud to the lower control arm. Estimated value based on common bolt size.
5 Ball Joint Nut
M12 x 1.75
5
Ball Joint Nut
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the ball joint stud to the steering knuckle or control arm.
6 Tie Rod End Nut
M12 x 1.5
6
Tie Rod End Nut
M12 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Secures the tie rod end to the steering knuckle.
7 Sway Bar Link Nut
M10 x 1.5
7
Sway Bar Link Nut
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Attaches the sway bar links to the sway bar and strut or control arm.
8 Sway Bar Mounting Bracket Bolts
M8 x 1.25
8
Sway Bar Mounting Bracket Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the sway bar mounting brackets to the chassis. Estimated value based on common bolt size.
Rear Suspension
1 Rear Upper Control Arm Bolts/Nuts
M12 x 1.75
1
Rear Upper Control Arm Bolts/Nuts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the rear upper control arm to the body/subframe. Estimated value based on common bolt size.
2 Rear Lower Control Arm Bolts/Nuts
M14 x 2.0
2
Rear Lower Control Arm Bolts/Nuts
M14 x 2.0
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Secures the rear lower control arm to the body/subframe. Estimated value based on common bolt size.
3 Trailing Arm Bolts/Nuts
M14 x 2.0
3
Trailing Arm Bolts/Nuts
M14 x 2.0
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Secures the trailing arm to the body/subframe. Estimated value based on common bolt size.
Subframe
1 Subframe Mounting Bolts
M14 x 2.0
1
Subframe Mounting Bolts
M14 x 2.0
Torque Specification
1. 80 ft-lbs (108 N·m)
2. 90°
Important Notes
Secures the front and rear subframes to the vehicle's chassis. Angle tightening procedure must be followed.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the proper torque for spark plugs on a 2014-2020 Acura RLX?
Q1
What IS the proper torque for spark plugs on a 2014-2020 Acura RLX?
Tighten the spark plugs to 12 ft-lbs (16 N·m) for non-projected-type spark plugs. For projected-type spark plugs, tighten to 18 ft-lbs (24 N·m).
Q2 What type of torque wrench should I use for lug nuts?
Q2
What type of torque wrench should I use for lug nuts?
Use a calibrated torque wrench with a range that covers the specified torque value for lug nuts. For 2014-2020 Acura RLX, the lug nuts torque specification IS 89 ft-lbs (120 N·m).
Q3 How do I convert torque values from ft-lbs to N·m?
Q3
How do I convert torque values from ft-lbs to N·m?
To convert ft-lbs to N·m, multiply the ft-lbs value by 1.356. For example, to convert 10 ft-lbs to N·m, multiply 10 by 1.356, which equals 13.56 N·m.
Q4 What happens if I over-tighten a bolt?
Q4
What happens if I over-tighten a bolt?
Over-tightening a bolt can stretch or damage the threads, making it difficult to remove or causing the bolt to fail prematurely. Follow the specified torque values provided in the service manual.
Q5 IS it necessary to use thread locker on bolts for the Acura RLX?
Q5
IS it necessary to use thread locker on bolts for the Acura RLX?
Refer to the Acura service manual for specific recommendations on which bolts require thread locker. Do not use thread locker unless it IS specified.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to the specified torque values provided in the service manual. This range IS suitable for most applications on the 2014-2020 Acura RLX.
- Digital display for clear and easy readings.
- Audible signal to indicate when the target torque IS reached.
- Reversible ratcheting mechanism for ease of use.
- Multiple units (Nm, ft-lb, in-lb) for versatility.
- Can be used on a wide range of vehicles and applications.
Service Procedures
Engine Bolt Torque Specifications
Step-by-step instructions for tightening engine bolts to the correct torque for 2014-2020 Acura RLX models.
- Locate the specific engine bolt that needs to be tightened.
- Refer to the service manual for the specified torque value for that particular bolt.
- Set the digital torque wrench to the desired torque value.
- Tighten the bolt using the torque wrench until the audible signal indicates the target torque has been reached.
- Ensure that the bolt IS properly tightened by checking its tightness with a standard wrench.
Suspension Bolt Torque Specifications
Step-by-step instructions for tightening suspension bolts to the correct torque for 2014-2020 Acura RLX models.
- Locate the specific suspension bolt that needs to be tightened.
- Refer to the service manual for the specified torque value for that particular bolt.
- Set the digital torque wrench to the desired torque value.
- Tighten the bolt using the torque wrench until the audible signal indicates the target torque has been reached.
- Ensure that the bolt IS properly tightened by checking its tightness with a standard wrench.
Brake Bolt Torque Specifications
Step-by-step instructions for tightening brake bolts to the correct torque for 2014-2020 Acura RLX models.
- Locate the specific brake bolt that needs to be tightened.
- Refer to the service manual for the specified torque value for that particular bolt.
- Set the digital torque wrench to the desired torque value.
- Tighten the bolt using the torque wrench until the audible signal indicates the target torque has been reached.
- Ensure that the bolt IS properly tightened by checking its tightness with a standard wrench.
Technical Service Bulletins
Updated Engine Bolt Torque Specifications
2023-02-10Important information regarding updated engine bolt torque specifications for 2014-2020 Acura RLX models.
2014-2020 RLX
Resolution: Refer to the updated service manual for the revised torque specifications and follow the instructions provided in the service procedures section to ensure proper tightening.
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.